Pinned Tweet
A lot of you have offered to and asked how you can support the lathe build, and since this is all so new to me, I didn’t really know how to answer that and haven’t felt comfortable just straight up asking people for money or specific parts. So after getting some suggestions and input from others, I finally set up something I feel comfortable with. No pressure at all, following along and sharing the build honestly helps just as much.
To be clear, I’m completely okay with funding this entire thing myself, I just can’t make any real promises on when it would be done. As the design grew into v2, the parts list grew with it and ended up costing way more than I originally intended. I’m a college student paying my own way through school, so I’ve been covering what I can with my own money and by returning parts I no longer need, and any help keeps me on track to have it running and cutting by this spring semester.
If you’re interested in supporting the build along the way, I started a Patreon at patreon.com/VinnyDynamics. Tiers start at $5 and range from your name in the credits of the open source release up to the in-depth engineering behind every decision (the calcs, the FEA and why each part ended up the way it did), early access to the CAD before it goes public, and a monthly Q&A. The first 30 founding members also get their name on a founders plate on the lathe and a custom stainless steel ring made on it once it’s cutting.
If you’d rather do a one-time thing, X Money works right from my profile, or Venmo (Vinnymace). And if you’d rather talk privately or want to help with a specific part, feel free to DM me.
Everything goes open source once it’s proven, so the CAD stays free no matter what, and nothing changes about the updates here on X. Patreon just gets the extra niche technical stuff like the actual FEA reports and calcs. I love showing anyone and everyone interested the build and progress on here, so none of that is going anywhere. The card below shows exactly where the money goes.
Huge thank you to the anonymous supporter who sent the first bit through X Money, to Clay (@SCH_Clay) for the servo, and of course @sendcutsend, thank you guys for being the first to back the project. Never expected any of this from what started as a passion project.
Feel free to drop any questions or concerns under this post. I’d really like feedback, especially on the Patreon side, since I had no idea what should be included in the tiers or what they should cost. I want this project to be for everyone, hence the decision to go fully open source, so don’t hesitate to give suggestions on how I could approach this better for everyone who’s graciously decided to follow along.
This project is starting to feel more and more real as the days go on, crazy to think this was just an idea 4 months ago and now we got the axis drive motors
16
633
Messing around some potential color scheming options to powder coat the sheet metal pieces, leaning towards the orange with this setup but anyone got any other suggestions?
Ayyy we got our 3000w transformer, lowkey scared to test the servo in my apartment on its shitty 1950s 15A circuits but hey, we shall see what happens when that gets here
3
18
651
Finally just put in a big parts order for the v2 lathe with @sendcutsend, got 19 laser cut and bent parts for stuff like the motor mount, belt cover, backsplash, ship tray, and others (everything in orange). Spent a good amount of time the past two days checking and rechecking these parts so that hopeful nothing needs correcting or can't be done properly. (First time actually designing for sheet metal) Once again just wanna say a huge thank you to @sendcutsend for offering support on the build so, cant wait to get the parts in sometime next week.
The waiting is over, lathe parts are finally being cut. Its taken some time to iron things out since making the v2 changes but now that I know which parts are final and not changing, stuff is gettin made. Unfortunately only had 2 hours to spare today for the shop so just started getting this nice ole block of 17-4 PH squared to get ready to start being milled into 2 of the tool blocks starting on monday. Also took a while to find a shell mill that had the right inserts to cut this stuff cleanly and shiii did it do a great job, unfortunately lacking on good carbide here but we make do.
1
18
560
Obtained some incredible pieces of stock from my friend @genZmfg which I am incredibly grateful for, we got the 17-4 PH that will attempted, key work attempted to be used to make the tool blocks IF i can actually machine it in my schools shop lol. A big ole chunk of titanium, a rod of Inconel that I have no idea what to do with and some good ole 1018 steel which will likely be one of or the first piece of stock used to do tap tests and see how well my models hold up. Also some other useful goodies that'll be helpful throughout the build process, again thank you Ryan 🙏
Ayyy, first @noxmetals order for the lathe just came in, excited to finally get to actually cutting metal. I actually ordered this back before this project blew up for the v1 design and as I have mentioned, the design has changed massively since then so not all of it is going where it was originally intended lol. Got the cast plate for the carriage which luckily still fits, still using the 6061 foot flange pieces + end caps, and the big ole 4" round that was meant to be the spindle pulley is now being turned into the encoder drive cap/mounting enclosure but hey at least its getting used. Gonna end up using the rest for other random little bits and pieces, and some fixtures most likely so it ain't going to waste. Also honestly really cool they take the time to write hand written notes like this seemingly for every customer especially given the relatively small size and cost of this order. Really impressed with everything about this order and the process and simplicity of it. Massive kudos to the team over there at Nox
2
19
888
Finally get to start cutting metal soon! Should start seeing actual parts being made in the shop over the next few weeks!
9
446
To add to the last 2 more serious posts, face reveal i guess lmao, wanted my profile to not look like a shitty throw away account anymore and to take this a bit more serious
3
348
As I promised, I ended up working on v2 pretty much all day yesterday, stayed up till close to 3am lmao and then have been working on getting it as close to finished since I've been back from our FSAE test day around noon today. In that time,I raised the headstock 8 mm, switched the way covers to off the shelf bellows, and finished the swappable steel gang blocks in CAD.
The raise came from making the steel plate under the headstock thicker, so nothing else on the headstock changed (headstock itself will likely be upgraded down the road). Long parts went from about 2.6 in to 3.2 in diameter, which is right at what the chuck can grip, and it only costs about 2% stiffness at the front turning tool. The chuck itself is also one of the things that will eventually need to change as the 4" is the limiting factor now.
The tool blocks are 4140 pre-hard holders that bolt to the cross slide in a front and back row, so tools can get swapped or rearranged without touching the rest of the machine. Parting runs off the back row with the spindle in reverse.
Way covers are off the shelf now too, a flat pleated cover on the headstock side and a McMaster bellows cut down for the tail side, about $77 for both instead of a custom set.
The 1.5 kW servo should land in the next couple weeks, so hopefully I'll be able to get that setup on a test rig with the headstock soon and start testing the intended setup and figuring out the specifics of how they will actually integrate with each other outside of the perfect world of CAD.
Please give any new feedback, as always thank yall for the support 🙏
Imma try and finish updating the CAD for this new version today, will stay up till 3am again if I have to. Will keep yall posted on how this turns out, will be looking for suggestions/critiques because the whole point of v2 is to take what everyone has said into account and improve on the things I missed on v.5 and v1. I have my gaps so I appreciate any real insight/advice on what I may still be messing up🙏
2
5
522
Full detailed project breakdown finally! Addressed many of the common questions and concerns, along with some changes and a few other things. It's a pretty long, technical read so be prepared lol. For those who won't end up reading it through, I want to give a massive thanks to everyone for all the support and attention this project has gained. Literally has been one of the most surreal 24hrs in my life
I’ve finally caught up on almost everything from the last 24 or so hours, so here’s the full breakdown of the lathe I promised, plus some big news on where it’s headed. First, a huge thank you to @sendcutsend for sponsoring the project, to @SCH_Clay for the shout that started all of this and for covering a new servo for the spindle, and to everyone who’s offered parts, machining help, advice and support. I went from 15 followers to a lot over 1000x that in less than a day, still blown away.
First thing I wanted to say is that It’s going open source
I’m officially going to open source this once it’s done and proven out. I’ll publish everything for every version, the CAD, drawings, BOMs with costs, build notes and machine settings, so anyone can build one. There are going to be three versions.
v0.5 is the cheapest way in. It’s a 24" bed with a 3/4 HP three phase motor on a VFD off a regular 120V outlet, running grbl on an Arduino Mega with NEMA 17s.
v1 is the same frame and spindle with grblHAL on a Teensy 4.1 and closed loop NEMA 23s.
v2 is the one I’m building since I have gotten the SCS sponsorship, the help from Clay, and a few other things and I cannot express enough how much I appreciate that support. It takes everything I learned designing v1 and everything from your replies, with a servo spindle, a longer bed, a stiffer Z axis, swappable gang tooling and real chip handling. Most of this post is about v2.
This fall I started training on the lathes in the machine shop at school where I work, fell in love with the lathes, and wanted a CNC lathe of my own I could use to make parts for my other projects. Before designing anything I priced out the mini lathes and what it would take to convert one. A converted 7x12 came out costing as much as building my own or more, the ones in my original budget have about 2" of swing over the cross slide and not much spindle torque, and nobody sells a ready made CNC conversion kit for them anymore. So I decided to design my own, which felt was a more worthwhile endeavor anyway.
The requirement I originally designed to is mild steel at 0.050" off the diameter in one pass (0.025" depth of cut) and light cuts in stainless. Almost every decision on the machine came from working out the stiffness and motor torque needed to hit that.
v0.5 and v1 are fully designed in SolidWorks, over 120 parts, and I’m actively redesigning the parts that change for v2 now. The build started at the end of October. It is not running or cutting yet. The first parts I’ve machined are the tram blocks, the push screw blocks that let me square the headstock to the Z axis. I'm looking to have most of the machining done by winter break so I can actually get to building it, and the goal is to have it cutting by the middle of the spring semester, ideally ironed out before the summer if I can. Really going to try and hold myself to this but I do have limitations given most of the work will be done in my school's shop.
Before locking in v2 I ran a full limitations study on v1, every axis, the structure, heat and accuracy, to find what would actually hold it back. v2 fixes most of what it turned up.
The base is an 8x4" steel rectangular tube with a 1/4" wall, bolted together with no welds since I'm kinda shit at welding lmao. On v2 it’s 27" long instead of 24", which buys a lot more Z travel. Across the top is a self leveling epoxy pour, and the top of that pour is the plane the linear rails and the headstock both sit on, so they come out coplanar without having to machine a bed.
Specifically to address the question from someone, the headstock is a bought Sieg C2 mini lathe casting with an upgraded spindle that takes a 4" chuck. I picked the C2 because it was the only headstock I could find with real drawings to design around, and buying a bored and finished spindle housing saves a lot of precision work that would've ate up a massive amount of time and money. I’m swapping the stock deep groove bearings for a preloaded pair of 7206 angular contact bearings, which drop into the same bores. The casting sits on a 3/4" steel T shaped spreader plate bolted across the tube, it’s located by a V key strip, and the tram blocks push it square to the Z axis. I stripped and measured the casting this week and to make sure the cheap chinese casting was accurate to the drawings and my CAD model.
As for the axis, Z rides on two 20 mm profile rails with four carriages. On v2 the rails are longer and shifted toward the tail end, which takes Z travel from about 6.8" to about 11". The Z ballscrew is the first thing that chatters on v1, so v2 goes to a bigger preloaded double nut ballscrew with heavier end supports and a gusseted nut bracket. X is a cross slide on two MGN12 rails with two blocks per rail on a 12 mm ballscrew. When I added up every joint between the tool and the bed, the cross slide on one block per rail let the tool shift about 30 microns under a full cut, and going to two blocks per rail took that to about 2. On v2 I’m also moving the X screw’s fixed bearing to the inner end, which cuts how much the diameter drifts as things begin to warm up by about 14 times, and a slightly longer X screw takes X travel from about 4.5" to a little over 5" so a rear row of tools can reach anything the chuck can hold
For everyone who asked about the motor and such, the original plan, and what v0.5 and v1 still use, was a 3/4 HP three phase motor on a VFD off a regular 120V outlet, belted to the spindle. That motor was one of the main limits on the machine. At carbide speeds it ran out of power before the rest of the machine did, it needed belt changes to get torque down low, and on a stop the chuck would coast for a long time. @SCH_Clay graciously helped obtain a servo, and after a lot discussion and input v2 gets a 1.5 kW AC servo on a 2 to 1 toothed belt. Which is basically the BLDC plus FOC setup a few people suggested, just in a kit that’s rated for continuous use. Through the belt that’s almost 10 Nm at the spindle all the time and almost 30 Nm in bursts, with full torque from zero rpm and a electronically braked stop instead of the chuck coasting. The mount takes other pulley pairs too, so I can go to 2.5 to 1 for more torque on bigger stock or 1.5 to 1 for more speed. Since I only readily have access to 120v it runs off a step up transformer, which caps it under 1 kW of continuous cutting power. And for safety, the spindle is capped at 2500 rpm until it has a proper enclosure.
For those who have asked the controls questions, v0.5 runs grbl on an Arduino Mega with NEMA 17s I already had, to get it moving fast. v1 and v2 run grblHAL on a Teensy 4.1 with closed loop NEMA 23s. For threading, there will be an encoder belted to the back of the spindle so grblHAL knows exactly where the spindel is and can do proper threading, since the Z axis has to move in step with the spindle. To be straightforward, this part is my biggest knowledge gap on this whole project, so I’m learning as I go with this and have been taking a lot of advice and guidance from several people more knowledgeable on this aspect. With that said I’m planning to run to a finer encoder so it tracks better at low speeds rather than just using the servo's built in one, and I'd like to get constant surface speed working for facing as again suggested by Clay.
For tooling, it uses gang tooling with 12 mm shank tools, so there’s no turret or tool changer. On v0.5 and v1 the tools sit in a basic gang block setup so you can swap them out for the task/job at hand in the moment but this leaves the issue of them losing their offsets and having to readjust said offsets when changing the tools almost every time. For v2 I’m making the blocks easier to swap so any tool can go in any slot at any time, a turning tool up front to get right up to the chuck, a parting tool or boring bar behind it, or a drill on center. I’m taking a lot inspiration from and looking at how production gang lathes handle quick change tooling so a block can come off and go back on without losing its offsets and of course welcome any advice or recommendations on how to improve upon this or where it could go wrong.
For the many people asking about how I'm dealing with chips and evac of them, on v0.5 and v1 it’s a flat deck with a removable cover over the Z screw and rails, a chip wall on the X and a chuck guard. That’s fine for proving it out on small cuts, but it won’t hold up long term. Based on the suggestions, all models around got to get bellows over the rails and screws, covers over the X rails and screw, and for v2 it'll get a chip tray the whole machine sits in and bolts through, so chips land somewhere I can just dump out. A slant bed is on the list for a potential future version as that becomes something that would either be too expensive or unrealistic to do in a reasonable amount of time given my constraints with being in school full time and doing this in my school shop.
When it comes to how its getting made, most of it will be done by me on 2 and 3-axis mills with some manual lathe work in the shop at school where I work to keep it simple and replicable. Laser cut and CNC machined flat parts come from @sendcutsend, the control panel is set to be 3D printed, and the deck is the epoxy pour I had mentioned.
As to the capabilities and where it'll actually be limited; going by my models, v1 should rough mild steel at around 0.020" to 0.030" depth of cut, with the Z ballscrew as the first thing to chatter. With the stiffer Z and the servo, v2 should more than double that to around 0.060" in mild steel on a 1" bar, which is 0.120" off the diameter in one pass. Stainless is harder to call because my models are somewhat sensitive and kinda swing back and forth because of the frequency the X axis vibrates at and the model freaks tf when that gets too close to the spindle's freq, but it should be somewhere in the ballpark of 0.020-0.030" but that still will have to be confirmed. At that point the limit in mild steel is how hard a 4" 3 jaw chuck can grip the part, not the machine. On a 120V outlet the deepest cuts have to run a bit slower than ideal carbide speeds, and on bigger stock the spindle torque sets the depth, which is what the 2.5 to 1 pulleys are for. It should hold around half a thou on diameter with a finish pass once it’s warmed up. There’s no tailstock yet, so work can only stick out about 2 times its diameter, and the longer bed leaves room to add one. Parting really has no limit besides how its positioned in the gang block/how much stickout it has. On accuracy, the things I’ll be fighting are X backlash and heat, so I’ll be re-touching off and warming it up before finish passes.
As to what's next, I'm going to be finishing the v2 design changes, working on getting the parts machined, sending off stuff to SCS, getting as much of the build put together over break, get it cutting in the spring, then tune it and get threading working. After that it's a tailstock, and further down the road maybe live tooling or a small mill add-on. Once it's cutting and proven out to my standards I'll publish all three versions with a full BOM and costs for each.
If anyone has more questions, drop them below and I'll happily keep answering. Thanks again everyone, this has been one of the most unreal 24hrs in my life 🙏
4
579
I’ve finally caught up on almost everything from the last 24 or so hours, so here’s the full breakdown of the lathe I promised, plus some big news on where it’s headed. First, a huge thank you to @sendcutsend for sponsoring the project, to @SCH_Clay for the shout that started all of this and for covering a new servo for the spindle, and to everyone who’s offered parts, machining help, advice and support. I went from 15 followers to a lot over 1000x that in less than a day, still blown away.
First thing I wanted to say is that It’s going open source
I’m officially going to open source this once it’s done and proven out. I’ll publish everything for every version, the CAD, drawings, BOMs with costs, build notes and machine settings, so anyone can build one. There are going to be three versions.
v0.5 is the cheapest way in. It’s a 24" bed with a 3/4 HP three phase motor on a VFD off a regular 120V outlet, running grbl on an Arduino Mega with NEMA 17s.
v1 is the same frame and spindle with grblHAL on a Teensy 4.1 and closed loop NEMA 23s.
v2 is the one I’m building since I have gotten the SCS sponsorship, the help from Clay, and a few other things and I cannot express enough how much I appreciate that support. It takes everything I learned designing v1 and everything from your replies, with a servo spindle, a longer bed, a stiffer Z axis, swappable gang tooling and real chip handling. Most of this post is about v2.
This fall I started training on the lathes in the machine shop at school where I work, fell in love with the lathes, and wanted a CNC lathe of my own I could use to make parts for my other projects. Before designing anything I priced out the mini lathes and what it would take to convert one. A converted 7x12 came out costing as much as building my own or more, the ones in my original budget have about 2" of swing over the cross slide and not much spindle torque, and nobody sells a ready made CNC conversion kit for them anymore. So I decided to design my own, which felt was a more worthwhile endeavor anyway.
The requirement I originally designed to is mild steel at 0.050" off the diameter in one pass (0.025" depth of cut) and light cuts in stainless. Almost every decision on the machine came from working out the stiffness and motor torque needed to hit that.
v0.5 and v1 are fully designed in SolidWorks, over 120 parts, and I’m actively redesigning the parts that change for v2 now. The build started at the end of October. It is not running or cutting yet. The first parts I’ve machined are the tram blocks, the push screw blocks that let me square the headstock to the Z axis. I'm looking to have most of the machining done by winter break so I can actually get to building it, and the goal is to have it cutting by the middle of the spring semester, ideally ironed out before the summer if I can. Really going to try and hold myself to this but I do have limitations given most of the work will be done in my school's shop.
Before locking in v2 I ran a full limitations study on v1, every axis, the structure, heat and accuracy, to find what would actually hold it back. v2 fixes most of what it turned up.
The base is an 8x4" steel rectangular tube with a 1/4" wall, bolted together with no welds since I'm kinda shit at welding lmao. On v2 it’s 27" long instead of 24", which buys a lot more Z travel. Across the top is a self leveling epoxy pour, and the top of that pour is the plane the linear rails and the headstock both sit on, so they come out coplanar without having to machine a bed.
Specifically to address the question from someone, the headstock is a bought Sieg C2 mini lathe casting with an upgraded spindle that takes a 4" chuck. I picked the C2 because it was the only headstock I could find with real drawings to design around, and buying a bored and finished spindle housing saves a lot of precision work that would've ate up a massive amount of time and money. I’m swapping the stock deep groove bearings for a preloaded pair of 7206 angular contact bearings, which drop into the same bores. The casting sits on a 3/4" steel T shaped spreader plate bolted across the tube, it’s located by a V key strip, and the tram blocks push it square to the Z axis. I stripped and measured the casting this week and to make sure the cheap chinese casting was accurate to the drawings and my CAD model.
As for the axis, Z rides on two 20 mm profile rails with four carriages. On v2 the rails are longer and shifted toward the tail end, which takes Z travel from about 6.8" to about 11". The Z ballscrew is the first thing that chatters on v1, so v2 goes to a bigger preloaded double nut ballscrew with heavier end supports and a gusseted nut bracket. X is a cross slide on two MGN12 rails with two blocks per rail on a 12 mm ballscrew. When I added up every joint between the tool and the bed, the cross slide on one block per rail let the tool shift about 30 microns under a full cut, and going to two blocks per rail took that to about 2. On v2 I’m also moving the X screw’s fixed bearing to the inner end, which cuts how much the diameter drifts as things begin to warm up by about 14 times, and a slightly longer X screw takes X travel from about 4.5" to a little over 5" so a rear row of tools can reach anything the chuck can hold
For everyone who asked about the motor and such, the original plan, and what v0.5 and v1 still use, was a 3/4 HP three phase motor on a VFD off a regular 120V outlet, belted to the spindle. That motor was one of the main limits on the machine. At carbide speeds it ran out of power before the rest of the machine did, it needed belt changes to get torque down low, and on a stop the chuck would coast for a long time. @SCH_Clay graciously helped obtain a servo, and after a lot discussion and input v2 gets a 1.5 kW AC servo on a 2 to 1 toothed belt. Which is basically the BLDC plus FOC setup a few people suggested, just in a kit that’s rated for continuous use. Through the belt that’s almost 10 Nm at the spindle all the time and almost 30 Nm in bursts, with full torque from zero rpm and a electronically braked stop instead of the chuck coasting. The mount takes other pulley pairs too, so I can go to 2.5 to 1 for more torque on bigger stock or 1.5 to 1 for more speed. Since I only readily have access to 120v it runs off a step up transformer, which caps it under 1 kW of continuous cutting power. And for safety, the spindle is capped at 2500 rpm until it has a proper enclosure.
For those who have asked the controls questions, v0.5 runs grbl on an Arduino Mega with NEMA 17s I already had, to get it moving fast. v1 and v2 run grblHAL on a Teensy 4.1 with closed loop NEMA 23s. For threading, there will be an encoder belted to the back of the spindle so grblHAL knows exactly where the spindel is and can do proper threading, since the Z axis has to move in step with the spindle. To be straightforward, this part is my biggest knowledge gap on this whole project, so I’m learning as I go with this and have been taking a lot of advice and guidance from several people more knowledgeable on this aspect. With that said I’m planning to run to a finer encoder so it tracks better at low speeds rather than just using the servo's built in one, and I'd like to get constant surface speed working for facing as again suggested by Clay.
For tooling, it uses gang tooling with 12 mm shank tools, so there’s no turret or tool changer. On v0.5 and v1 the tools sit in a basic gang block setup so you can swap them out for the task/job at hand in the moment but this leaves the issue of them losing their offsets and having to readjust said offsets when changing the tools almost every time. For v2 I’m making the blocks easier to swap so any tool can go in any slot at any time, a turning tool up front to get right up to the chuck, a parting tool or boring bar behind it, or a drill on center. I’m taking a lot inspiration from and looking at how production gang lathes handle quick change tooling so a block can come off and go back on without losing its offsets and of course welcome any advice or recommendations on how to improve upon this or where it could go wrong.
For the many people asking about how I'm dealing with chips and evac of them, on v0.5 and v1 it’s a flat deck with a removable cover over the Z screw and rails, a chip wall on the X and a chuck guard. That’s fine for proving it out on small cuts, but it won’t hold up long term. Based on the suggestions, all models around got to get bellows over the rails and screws, covers over the X rails and screw, and for v2 it'll get a chip tray the whole machine sits in and bolts through, so chips land somewhere I can just dump out. A slant bed is on the list for a potential future version as that becomes something that would either be too expensive or unrealistic to do in a reasonable amount of time given my constraints with being in school full time and doing this in my school shop.
When it comes to how its getting made, most of it will be done by me on 2 and 3-axis mills with some manual lathe work in the shop at school where I work to keep it simple and replicable. Laser cut and CNC machined flat parts come from @sendcutsend, the control panel is set to be 3D printed, and the deck is the epoxy pour I had mentioned.
As to the capabilities and where it'll actually be limited; going by my models, v1 should rough mild steel at around 0.020" to 0.030" depth of cut, with the Z ballscrew as the first thing to chatter. With the stiffer Z and the servo, v2 should more than double that to around 0.060" in mild steel on a 1" bar, which is 0.120" off the diameter in one pass. Stainless is harder to call because my models are somewhat sensitive and kinda swing back and forth because of the frequency the X axis vibrates at and the model freaks tf when that gets too close to the spindle's freq, but it should be somewhere in the ballpark of 0.020-0.030" but that still will have to be confirmed. At that point the limit in mild steel is how hard a 4" 3 jaw chuck can grip the part, not the machine. On a 120V outlet the deepest cuts have to run a bit slower than ideal carbide speeds, and on bigger stock the spindle torque sets the depth, which is what the 2.5 to 1 pulleys are for. It should hold around half a thou on diameter with a finish pass once it’s warmed up. There’s no tailstock yet, so work can only stick out about 2 times its diameter, and the longer bed leaves room to add one. Parting really has no limit besides how its positioned in the gang block/how much stickout it has. On accuracy, the things I’ll be fighting are X backlash and heat, so I’ll be re-touching off and warming it up before finish passes.
As to what's next, I'm going to be finishing the v2 design changes, working on getting the parts machined, sending off stuff to SCS, getting as much of the build put together over break, get it cutting in the spring, then tune it and get threading working. After that it's a tailstock, and further down the road maybe live tooling or a small mill add-on. Once it's cutting and proven out to my standards I'll publish all three versions with a full BOM and costs for each.
If anyone has more questions, drop them below and I'll happily keep answering. Thanks again everyone, this has been one of the most unreal 24hrs in my life 🙏























