Nicki Jensen retweeted
How could this not be bigger headlines than Tesla 2 million OTA over ”wheel nag” is out of my understanding!
”Daihatsu admitted in April that it fudged crash test results on 88,000 cars”
—————————
Toyota vows reform after affiliate Daihatsu caught in safety scandal
An investigation that found that vehicles were not properly tested for collision safety.
Toyota pledged "fundamental reform" after subsidiary Daihatsu was forced to suspend all shipments following an investigation that found most of its vehicles were not properly tested for collision safety.
An independent panel has been investigating Daihatsu after the brand said in April it had rigged side-collision safety tests carried out for 88,000 small cars.
Toyota said in a statement Wednesday that around 174 irregularities have been identified across 64 models, including in some cars sold under the Toyota brand.
The move to suspend Daihatsu's shipments will affect vehicles produced in Japan and overseas, and not only at Toyota factories but possibly also at companies like Mazda and Subaru, considering Daihatsu provides manufacturing services to a range of other automakers.
Previously, only about half a dozen models were thought to be affected by the manipulated test results, but Toyota now says almost every car in Daihatsu's line-up could be impacted. The latest revelations suggest the scope of the scandal is far greater and went back much further than previously thought and could potentially tarnish the automakers' reputation for quality and safety.
Airbag control unit
The investigation centers around cars' airbag control unit and found that the ones used during crash tests were different from the ones used in cars actually sold to the public, including Toyota's Town Ace and Pixis Joy models and the Mazda Bongo.
While those other test units were later found to meet industry standards, side-collision test results of the Daihatsu Cast and Toyota Pixis models "may not comply with the law," Toyota said.

Toyota said it's not aware of any accidents or incidents related to the issue. The company said it could not yet determine the financial impact of the matter.
Daihatsu admitted in April that it fudged crash test results on 88,000 cars that were manufactured in Thailand and Malaysia and sold within the past year.
Nicki Jensen retweeted
The 48V gigabit Ethernet loop and steer & brake by wire pave the way for the new unboxed process of Teslas Gen3 vehicle. Have a read ⤵️
The assembly line introduced back in 1930 by Henry Ford was revolutionary and has made producing cars faster and cheaper. Of course there were implemented now methods over time like welding or robots that made manufacturing faster and more precise which increased speed and quality. But all in all it is still the whole car body that runs the line till it is fully completed. Here are the current steps:
1. Stamping: The car body parts, such as the doors, hood, trunk, and fenders, are cut and shaped from large sheets of metal using hydraulic presses and dies.
2. Welding: The car body parts are welded together using robots to form the car frame or chassis.
3. Painting: The car frame is cleaned, primed, painted, and dried in a paint shop using automated spray guns and ovens. (CT deleted this step 🔥)
4. Assembly: The car frame is moved to the final assembly line, where the electric motor, battery, suspension, wheels, tires, seats, dashboard, steering wheel, and other parts are installed. The electrical wiring, lights, airbags, and other systems are also connected and tested.
Tesla is using this process with ist current line up as well. They did further optimise it with large giga castings of the front and the rear and the 4680 structural battery. But what they showed at the Investor day in 2023 is a completely different animal and will change how cars are being built in the future.
The Unboxed Process
So how does the unboxed process works and why are 48V gigabit Ethernet loop and steer & brake by wire so important here:
So at the unboxed process, different pieces of the car will be assembled on their own, before the car will be finished as a whole. This allows more employees (or bots 🤖) to work on the car at the same time.
As Tesla pointed out on their Investor's day, this allows for a 44% operator density and a 30% space time efficiency improvement.
It all sounds well and good. But there are various problems if we would transfer the current state of the art to this new process.
The cable harness:
In conventional vehicles, the wiring harness is prefabricated by hand as a unit and warped in the entire car as u can see in the following picture. This would be difficult to achieve with the unboxed process since the various parts have to be already assembled.
So Tesla is using a bidirectional 48V gigabit Ethernet loop that connects all high speed controllers together. This saves a bunch of wiring bc. every endpoint, for example a speaker, does not has to be wired back to the amplifier, it simply is wired to the next high speed controller. This reduced the mass of the wiring in half. And it also paves the way for the unboxed process.
The idea is that every part, like the front for example, has ist own high speed controller. So when the individual finished part's of the car are getting married together, these part's of the car simply will be connected via the Ethernet loop and that's it.
Steer & brake by wire
As far as I know, the Cybertruck only uses steer by wire. The use of this system certainly makes the unboxing process easier, but since, unlike the CT, it would only affect the front of the compact car, this wouldn't be such a big problem. You could also build the front with conventional steering separately from the rest of the car.
However, if 4-wheel steering is used, as with the CT, the advantages are obvious. You don't have to create a mechanical connection between the front and the rear. A high speed data bus does the job. And who knows, maybe they will also be able to build bigger cars like vans with the gen3 platform, now 4-wheel steering would be a thing again.
But its completely different with brake by wire. If conventional brake lines with hydraulic brake fluid were used, the entire unboxed process would not be as easy as it sounds.
Through brake by wire the brakes are again connected to the next high speed controller and the thing is suddenly possible.
And since the wiring is already done as a loop it has already built in the necessary redundancy for steer & brake by wire.
Final thoughts:
In my opinion, Tesla is making really well thought-out steps here. They are using new technology in a product like the Cybertruck, which promises high margins once production is ramped. This means that R&D costs can be quickly cushioned.
As soon as Tesla's new gen3 platform sees the light of day, you no longer have to worry about these basic technologies, as they have already been implemented in large numbers in the Cybertruck and have also been tested in reality over millions of kilometers.
Which doesn't mean the ramp of gen3 won't be complicated, but it certainly makes it a lot easier. What do u think?
Also have a read about all my top improvements that are not so obvious at the Cybertruck:
teapaw.org/MatHias8719/status/173…
We finally saw the first deliveries of the Cybertruck.
In addition to all the obvious and long-known features like stainless stell body, these are my top improvements that are not so obvious:
1. 48V architecture.
The 12V technology for electronics in cars was introduced 70 years ago and has replaced the 6V technology. Since then, no improvements have been achieved because suppliers and car manufacturers have been too inflexible to introduce new technologies.
When introducing the CT, Tesla thought: "Hold my beer" and has once again proven to be a technological leader not only when it comes to electric cars, but also when it comes to the basic structure of car electronics, which now play's a major role in every car, regardless of the drive system.
With the 48V system, a lot of copper can be saved in the cables because the power is the product of current and voltage. If the voltage is quadrupled, the current can be quartered in order to still send the same power through the cables. And since the power loss in the cables increases with the current strength, this results in a much lower resistance.
2. Steering by wire.
As I have written many times, I have been crying for this technology since the introduction of the Tesla MS Plaid. I could have bet that this was introduced back then or at least on the M3 Highland when they eliminated the stalks behind the wheel.
But as with many things, individual technologies at Tesla are ahead of others (see USS and Vision), which has earned them some criticism, especially in countries with many roundabouts.
Now the time has finally come with the CT. It is therefore possible to always keep your hands in the perfect spot so that you can reach the safety-relevant controls such as indicators and windshield wipers at any time.
In addition, this technology should also enable savings in production and will be necessary at Tesla in the future anyway to enable this in robotaxis.
Using this system with 4-wheel steering, wich was also introduced with the CT, was also helpful.
3. Tesla's Powershare
With this new system it is now finally possible to use the EV as an electricity storage for the house, charge other EV's or use high voltage devices on the go.
In my opinion, this is also key for the energy transition. Tesla has already impressively demonstrated with the Powerwall how well VPP works to relieve the power grid when necessary and thus make very expensive peak-load power plants unnecessary.
With the CT's 10x larger battery, you can easily imagine what untapped potential there is.
Additional advantages:
- Supply the house in the event of a long power outage for several days
- If the SC still has power, you could charge the CT and then continue to supply the house
- You can charge other EVs
- And as described in this post (see below), the possibility of being able to use electricity is particularly useful for workers such as road workers, forestry workers, etc. who do not have access to the power grid and have previously had to rely on diesel generators.
Also imagine a Tesla service mobile comes with a CT and gives u the extra boost while repairing your car.
4. 800V architecture
For the first time, the CT also introduces 800V for the drive batteries. However, this is nothing new. This was first introduced with the Prosche Taycan in 2019, but models such as the Hyundai Ioniq 5 and 6 also rely on this high voltage.
With this system, Tesla should be able to charge up to 350 kW on V4 Superchagers in the future. There were also contradictory statements that the CT could also load on MW chargers. However, this does not seem to be possible in the near future.
4. 4680 battery
The 4680 battery is the first battery designed and produced in-house by Tesla. This is revolutionary in many ways.
- It is used in the models as a structural component, which saves costs and weight.
- Because the contacts of the anode and cathode extend over the entire "length" of the theoretically rolled out battery to the outside, it is possible that the electrons travel the shortest possible path, which in turn means higher performance. This creates less heat than with other cylinder cells.
- The larger form factor allows more kWh to be produced in a shorter time.
The battery was already introduced in the MY made in Giga Texas. But these "Cybercells" were basically designed for the Cybertruck. In the future, however, it is expected that these cells will be produced and installed in all Gigafactories.
There is some criticism bx. of the range. It is only with a big REX-battery in the bed possible to come close to the 500km that were promissed at the unveiling. However, since this battery is in the very early stages of development it's clear that improvements will come.
In this regard I always think about the BMW i3. It was first introduced with a 22 kWh battery and had therefore a gasoline REX. After 5 years the same car had a battery size of about 42 kWh without needing more space for the battery.
Checkt out a real live example why power sharing is so important for outside workers:
teapaw.org/MatHias8719/status/172…
What did u like the most about the Cybertruck? Are you satisfied or is there something that is extremely bothering you?
Nicki Jensen retweeted
Tesla: we’re done waithing, and we are sick of suppliers not doing it, so we are just doing 48V everything.
Catch up!
Nicki Jensen retweeted
F I N A L L Y!!!!
B R E A K I N G ! ! !
Di reveals: Tesla is suing the state for suspended license plates
The electric car company Tesla is suing the state through the Swedish Transport Agency because the company does not get access to registration plates for new cars, Di can reveal.
"This seizure of license plates constitutes a discriminatory attack without any support in law directed at Tesla," the company writes.
In the documents submitted to the Norrköping district court on Monday, Tesla also demands that the district court give the company the opportunity to collect the signs from the sign manufacturer Scandinavian Motorcenter during the time that the matter is handled legally.
"Tesla requests that the district court obliges the Swedish Transport Agency to ensure that registration plates for the vehicles owned by Tesla, which have been registered in accordance with the regulation (2019:383) on vehicle registration and use, and which have been assigned a registration number by the Swedish Transport Agency, come into Tesla's possession," it says in the documents.
Di revealed last week that IF Metall's strike is resulting in Tesla not being issued license plates.
The background is that sympathy measures for IF Metall's strike against Tesla in the fight for collective agreements have meant that Postnord does not deliver mail to Tesla. The Swedish Transport Agency has in turn referred to the fact that you may only use Postnord as a mail provider because you follow the Kammarkollegiet's framework agreement for letter and parcel services. Through the agreement with the sign supplier, Tesla is also not allowed to collect the signs from the supplier, according to the Swedish Transport Agency.
“Our mission is to provide license plates through procured suppliers. We have completed this by taking the signs to Postnord," explained Anna Berggrund, Department Director Vehicle Information at the Swedish Transport Agency.
Tesla goes to strong criticism of the authority.
"Through this unprecedented action, the Swedish Transport Agency has become a deeply harmful instrument in the labor market conflict, which affects Tesla and above all it affects Tesla's employees and customers," the company writes in the court documents.
Tesla demands that the court decide on a so-called interim security measure and links it to a fine of one million kroner, or the amount that the district court finds reasonable, in order for Tesla to be able to collect the signs on its own.
"The interim security measure thus aims to ensure that Tesla and ultimately its customers are still provided with registration plates by self-collection during the time that the trial is ongoing, which can happen if the Swedish Transport Agency gives its consent to this. Such a consent is not burdensome for the Swedish Transport Agency, but on the contrary a trivially simple measure," Tesla believes, according to the lawsuit.
Nicki Jensen retweeted
This is insanity squared!!!🤬😡
🇸🇪 Tesla strike!
———————
Killing blow for Tesla: The cars do not get new license plates
IF Metall's strike will stop new Tesla cars from being put into service. The reason is the sympathy measure that blocks Postnord's handling of mail to Tesla.
According to the Swedish Transport Agency, registration plates may not be distributed in any other way.
Tesla rages against the "disproportionate action" of the authority and state-owned Postnord.
IF Metall's strike against Tesla in the fight for a collective agreement has almost lasted a month, but work at Tesla's facilities is still ongoing. There are staff who take care of cars that have arrived by truck and make them ready for customer delivery. Among other things, the number plates that normally arrive via Postnord are mounted.
But it will stop.
Tesla will henceforth not receive any new license plates because Postnord no longer handles mail for the electric car company. The Swedish Transport Agency may not change postal providers.
"The authority Kammarkollegiet has procured a framework agreement for letter and parcel services that all authorities must use. And according to that agreement, we must use Postnord," explains Anna Berggrund, department director Vehicle Information at the Swedish Transport Agency.
On Monday night, Seko's sympathy measure came into effect. It involves a blockade against the distribution, delivery and collection of shipments, letters, packages and pallets made by Postnord and Citymail to all of Tesla's workplaces throughout Sweden. The trade union ST's blockade concerning Postnord's deliveries to Tesla began to apply on Tuesday afternoon.
Anders Porelius, who is press manager at Postnord Sweden, confirms that all mail delivery to Tesla has been stopped.
"We are neutral in the basic conflict, but we do not bypass the blockade. Shipments destined for Tesla are not distributed. The right to strike is so strong that it counts as force majeure. This means that we are not violating the social mission," he says.
What does Postnord do with all mail to Tesla?
"We take care of it and store it," says Anders Porelius.
The Swedish Post and Telecommunications Board, which is the supervisory authority, is informed and announces via press officer Petter Öhrn that the issue is being followed.
There is no information on how many number plates are involved so far. Between January and October, roughly 17,000 new Teslas have been registered in Sweden, which means an average of 1,700 cars per month. New registrations have continued even since the strike broke out. Last week alone, approximately 500 new cars were delivered. The plates are ordered when the car leaves the factory so there will be a delay before the postal blockade hits the car deliveries.
The process of registering cars is the same for all car brands. New cars are registered by the Swedish Transport Agency and then an order is made for registration plates from the supplier with whom the Swedish Transport Agency has an agreement. It is Scandinavian Motorcenter (SMC) in Danderyd. But Tesla is not allowed to go there and collect the signs.
"Our agreement with SMC describes how the signs are to be distributed to ensure that the signs are delivered to the right recipients. The agreement does not allow signs to be handed out or picked up directly from the sign manufacturer," says Anna Berggrund.
She explains that the Swedish Transport Agency's responsibility is to ensure that the signs are manufactured.
“Our mission is to provide license plates through procured suppliers. We have completed this by taking the signs to Postnord," she says.
Tesla emphasized in a written statement to Di that the mail blockade "does not have an immediate impact on our delivery capability."
Nicki Jensen retweeted
Top 50 changes of the NEW @Tesla Model 3
1) ~10% increased range (629 km WLTP)
2) Slightly decreased top speed (201 km/h)
3) New matrix LED headlights
4) New exterior design
5) Lower drag coefficient (0.219 from 0.230). That's the lowest drag Tesla EVER
6) New wheel design
7) Improved suspensions
8) New colors (Ultra Red & Stealth Grey)
9) No more Tesla T logo on the back (T E S L A)
10) Brighter and more responsive touchscreen
11) New customizable ambient LEDs
12) New steering wheel
13) New materials
14) New center console design
15) New passenger display
16) New ventilated seats
17) New armrest with cup holders for the passengers
18) Decreased cabin noises
19) Upgraded ventilation system 2.0 (you can now decide to turn on or off the ventilation on each side of the front seats, but not on the rear)
20) Little price increase (around 1k)
21) 3 new stereo speakers: from 14 to 17
22) No performance model officially announced yet
23) New blind spot light integrated into the side speaker
24) New position for the windshield wipers water refilling in the front trunk department
25) 65 Watts USB-C charger port
26) Reinforced side doors, with a new downward lock (to comply with the new American safety regulations)
27) New FSD hardware 4
28) Higher camera resolution
29) No more water residues left by the windshield wipers on the front glass (improved visibility)
30) The front orange position lights have been integrated into the headlight cluster
31) New Tri-Band GPS module, which should guarantee greater precision in vehicle location
32) New buttons on the steering wheel, for example the "Cameras" button, which activates the view of the vehicle's external cameras on the screen
33) Trunk 30 liters larger than the previous one
34) Although the steering wheel is similar to that of the Model S and X, the horn remained in the center of the steering wheel, not on a button
35) New active feedback feel for the steering wheel buttons, improved compared to Model S and X (and they are not as sensible)
36) Slightly steeper rake on the bonnet, which pushes the air higher and reduces even more cabin noises
37) Skinnier air intake
38) There are no fog lights on the lower front (like, there are no more fog front lights at all)
39) New tires, supposedly softer (to help improve the ride)
40) New lower bumper on the back
41) New rear lights design (much cooler)
42) Rear lights are now all in one block (previously, when opening the trunk, they split in two)
43) New function introduced via the display in the passenger row, which allows you to move the front passenger seat completely forward, in case there is no one there and the passengers need more space
44) No more indicators stalks behind the steering wheel (deal with it)
45) Rear seats have a slightly different angle, to make the back rest a bit more comfortable
46) Instead of the old single microphone, there are now 2 of them, and each one of those is better than the previous one. Great for phone call quality.
47) New sound signal that is activated every time we go over the road speed limit
FOR INVESTORS:
48) Increased margins
49) Around 50% of new parts (aka better parts)
50) More efficiency (more with less, therefore fewer parts which implies less production time and costs, on top of a lighter vehicle)
Video from: @YouCarTV
Top 20 changes of the NEW #Tesla Model 3
1) Increased range
2) Slightly decreased top speed
3) New matrix LED headlights
4) New exterior design
5) Lower drag coefficient (0,219)
6) New wheel design
7) Improved suspensions
8) New colors
9) No more Tesla T logo in the back
10) Brighter and more responsive touchscreen
11) New ambient LEDs
12) New steering wheel
13) New materials
14) New center console design
15) New passenger display
16) New ventilated seats
17) New cup holders for the passengers
18) Decreased cabin noises
19) Upgraded ventilation system 2.0
20) New pric... oh no, actually the price remains the same
FOR INVESTORS:
1) Increased margins
2) Better overall vehicle (which means more sales)
3) More efficiency (more with less, therefore fewer parts which imply less production time and costs, on top of a lighter vehicle)
Video from: @YouCarTV
#Model3 #ElonMusk
Nicki Jensen retweeted
#DataInsights 75:
How has Tesla expanded superchargers over the past 11 years?
I saw these tweets from @SawyerMerritt & @superchargeinfo 2 weeks ago. There are 22.6k chargers available at these 2k locations
teapaw.org/SawyerMerritt/status/1…
This animates the data points by each year through Nov 3, 2023.
Nicki Jensen retweeted
🇸🇪The strike at Tesla - No one stood up
Promises of a strike against Tesla, organized by the trade union IF Metall, raised concerns among the company's customers. But when the day came, no one chose to stop their work. Tesla Club Sweden visited Tesla's service center in Infra City to get a closer look at the situation.
Friday's planned strike at Tesla, whose purpose was to cripple the company's operations, did not take place. Although there was great concern among customers, as they feared that they would not get their cars serviced, no signs of a work stoppage could be seen on site at Tesla in Infra City when Tibor Blomhäll from Tesla Club Sweden visited the facility on Friday.
”Don't want to strike because the working conditions and wages are better at Tesla compared to previous workplaces”
The company's business was in full swing: cars were being repaired, customers were dropping off and picking up their vehicles as usual. None of the employees had chosen to go on strike, and consequently no bookings had to be rescheduled.
Why did no one choose to strike?
The reporter took the time to talk to the workshop staff, who happily shared their views. They claimed they did not want to strike because their working conditions and wages were better at Tesla compared to previous workplaces. In addition, shift allowance and overtime pay are added to the salary, which also exceeds what other companies offer. The company also provides beneficial stock options, which, according to one young employee, helped him buy his first apartment.
Another employee pointed out that the average age of Tesla's workforce is lower than average and that working conditions are better than what this age group normally gets at other workshops. He also emphasized that there is strong cohesion and well-being in the workplace, which contributes to low staff turnover.
Tesla Club Sweden reports on this.
Employees' view of the union
When asked about their relationship with IF Metall and the union's demands, the employees said that they had met with union representatives on several occasions. However, these meetings had not been convincing, and they had not been attracted by what they were told. In addition, despite the union having a list of items that the employees lack, the employees say that their wages and working conditions are not only better than at other workshops, but also include full insurance and occupational pension.
According to the employees, only a small part of the staff is in the union, and those who are do so because of old habit. One technician pointed out that the fact that no one chose to strike should be a sign of what they think of the union and their methods.
Even at other Tesla centers around the country, only a few employees have chosen to strike. However, the employees we spoke to expressed a concern about possible reprisals, not from the employer, but from the union.
Nicki Jensen retweeted
🇩🇪 Giga Berlin used in the First Year only 17% of the Approved Water
Instead of the permitted 1.8 million cubic meters, Tesla in Grünheide used only 300,000 cubic meters of water in the first year, Environment Minister Vogel reported. And the same amount from January to August 2023, after production ramps up. Tesla is building around 250,000 Model Ys this year. Approved are 500,000. The corporation has applied for expansion to one million cars. "Without higher water consumption". The precious wet is to be completely recycled.
Tesla has been criticized for years for no reason because of water consumption in Giga Berlin. The company uses only a fraction of what other car manufacturers used and 83% less than admitted in the first year and after the ramp it will be still below 30%.
"In 2022, the amount of water withdrawn (in the region) decreased by 5.3 percent to 10.2 million cubic meters," Environment Minister Axel Vogel told the Potsdam state parliament on Thursday.
Despite this, the WSE water board has denied the necessary approval to 18 new construction projects in the region, including new businesses, a school and a residential area. Because allegedly the water is missing. Amazing, because: According to the Minister of the Environment, the WSE produces only two-thirds of the "practically usable" water volume of 14.9 million cubic meters per year. The water board did not respond to a B.Z. inquiry about the reasons.
The CEO of WSE recently survived a vote of no confidence and an election.
The Ministry of the Environment recently listed the real major consumers: 44.8 million cubic meters are consumed by the LEAG coal group for power plant cooling, 23 million cubic meters by the waste incineration plant in Premnitz (Havelland), 13.5 million by the PCK refinery in Schwedt. Even the Klaistow asparagus farm, with 1.09 million cubic meters, consumes more water than the Tesla plant with 11,000 jobs.
The double standards in Germany on the subject of water and Tesla are unbearable.
Nicki Jensen retweeted
According to my sources Chinese domestic cell prices are $70-75/kWh for LFP and $80-90/kWh for NMC. This is significantly lower than BMI’s weighted global cell price average of “below $100”. Note the numbers are not completely apples to apples but still interesting to compare.
Nicki Jensen retweeted
Thought experiment for Tesla owners — if everything about your car stayed the same but you could magically refill your battery the way gas cars are refilled (quickly at gas stations, but not at home), would you make that change?
74%No, keep car the same
26%Yes, refill like gas car
12,566 votes • Final results Nicki Jensen retweeted
According to Taiwan's Economic Daily News: TSMC (TSM.N) will get more orders for Dojo supercomputers from #Tesla (TSLA.O).
Nicki Jensen retweeted
"Gigacasting 2.0"
As reported by Reuters, the rumor is that Tesla is moving to casting the full underbody in one hit.
That is, casting the front and rear underbody in one machine along with the rocker or at least part of the rocker.
What do I mean by the rocker?
I'll do a subpost below with the video I did on the topic April of 2022.
reuters.com/technology/gigac…(,familiar%20with%20the%20move%20said.
Nicki Jensen retweeted
BREAKING: @Tesla has officially introduced Powerwall 3 on its website, along with its specs.
Highlights:
• Energy Capacity: 13.5kWh (same as before)
• Solar inverter directly integrated. 6 solar inputs (up from 4)
• On-Grid Power: 11.5 kW continuous
• Now flood resistant to over 2 ft
• Backup Power: 11.5kW continuous (64% more than before)
• System expansion available anytime. 40.5 kWh max addition per unit
• 287 lbs (16% lighter than Powerwall+)
• Dimensions: 43.25 in x 24 in x 7.6 in
• Tesla says Powerwall 3 is coming in 2024
Nicki Jensen retweeted
Debunking myths about burning BEVs:
On Tuesday night, 10 Tesla vehicles, among others, burst into flames in Frankfurt, Germany.
According to the fire department, the fire broke out at around 3 a.m. on Tuesday night in the parking lot of a car dealer in the Frankfurt district of Fechenheim. When the emergency services arrived, the fire had already spread to several Tesla vehicles.
After only one hour, the fire was extinguished with extinguishing foam.
Despite the fire, the 🔋 battery of none of the vehicles caught fire.
Ten Teslas burned out completely, and other vehicles were damaged by the fire. The cause of the fire is still under investigation. A total of 40 firefighters were deployed.
Nicki Jensen retweeted
I can't wait to read this book!
"Let me be clear," he said slowly.
"This vehicle must be designed as a clean Robotaxi. We're going to take that risk. It's my fault if it f--ks up. But we are not going to design some sort of amphibian frog that's a halfway car. We are all in on autonomy."
NEWS: In May 2023, Elon Musk decided to change the initial build location for the next-generation Tesla car & Robotaxis from Mexico to Austin, where his own workspace & that of his top engineers would be right next to the new ultra-automated assembly line. axios.com/2023/09/08/walter-…
Nicki Jensen retweeted
A small summary of the livestream from @tobilindh about the new (1 month old) expansion documents from Giga Berlin.
- There will be more powerful furnaces where they will be able to recycle all the scrap aluminum from both the stamping section and the casting section.
- Waste water treatment is changing so that now they will reuse all of the production waste water.
- There will be a new temporary tent village for storage, temporary cell testing building, a new warehouse and a new vehicle distribution area that is much bigger then the old one.
- Multiple new buildings for container storage and hazmat storage and battery recycling up on the north east side. The old concrete mixing plant will also move to this location.
- They have changed the plans for the entrance of the main factory building so that it is now accessible to the public. It seems like Tesla can't decide on entrances for their factories... @JoeTegtmeyer how many times have they changed the design in Giga Tx by now? 🤣
- To the right of the main building, there will be a dedicated medical building. Also a new bridge connecting the new train station with the parking lot and the rest of the factory.
- The new production building will be big, really big. It will be 700m by 700m and 25m high, bigger then Giga Texas! 🤯
The roof of the factory will be covered in parking space and solar panels, with a 15Mw peak.
- To store all this energy, there will be a Megapack installation with 30Mwh and a switchyard.
- There will be a complete new water recycling plant for this new factory.
Not much more information in these permits, but much more to come for sure.
Things like delivering cars via trains will happen in the future, but Tesla needs to buy more land first.
Everything and more is from the livestream from @tobilindh, thank you so much for doing this and please continu your awesome work! (If I made any mistakes please correct me)
youtube.com/watch?v=1j29jKqv…
If you are interested in more updates from Giga Berlin please follow @tobilindh. (And me too 😁)
@SERobinsonJr
@JoeTegtmeyer
@SawyerMerritt
@wholemars
@TeslaClubBE
@TeslaOwnersNL
@TeslaOwnersDEU
@alex_avoigt







































