@teraytech

Engineer | Tests & Measurements & Metrology Enthusiast

teraytech.cc/
Joined February 2016
  • Tweets1.8K
  • Following444
  • Followers4.9K
648Media
✧ 新作アバター『ソルト -Salt-』✧ 🎁 プレゼントキャンペーン✨ ✦参加方法 ① @komado_boothをフォロー ②この投稿をRP 🌟10/31(土) 23:59まで ✦ BOOTHのスキ♡で当選人数UP✨ 3名様＋♡1,000ごとに1名追加🐾 「ソルト -Salt-」はこちら ▼ komado.booth.pm/items/896283…
76
13,675
148
11,736
422,425
Introducing my new HAROGIC VNB-60 6GHz VNA 😋
6
9
107
3,432
It works so well, love it a huge improvement over libreVNA and the ECAL kit is a huge bonus too
3
332
Offer accepted! 🥳
68
11
5
813
17,932
Turned a WiFi 7 router into a 320Msps SDR. Custom firmware on its MediaTek MT7996 streams raw 14-bit IQ from 2.4/5/6GHz over 10GbE without dropping samples. It's not a snapshot mode, the waterfall is just one thing reading the stream. github.com/h0m3us3r/w1700k-s…
58
282
37
2,158
180,994
⋆⸜＼ ꙳⋆新作アバターのお知らせ ⋆꙳／⸝⋆ 新作アバター『ソルト -Salt-』🐟🩶 ラスクのきょうだいです🐾꙳⋆ ✧2026年11月発売予定✧
87
8,433
2,380
28,011
1,600,630
Tτ retweeted
keiiiii@Kei31451Oct 1
オフ会って感じ😙 楽しい
1
5
30
589
we built a lightning strike detector in just 2 days in partnership with @embedder_dev and open sourced it! the future of hardware is fast. a thread 🧵
54
133
15
1,782
167,455
Don't remove the screw that fixes the port on the shell, and you can get this👇
Dave Jones
@eevblogAug 11
Oh fuck. A literal teardown 😭
5
3
97
7,654
I designed a miniature, four-quadrant, high-voltage power supply that employs digital pre-regulation and a Class-AB output stage to achieve high-efficiency, precision output; it is primarily intended to provide bias voltage for the compensation electrode of an ionization chamber.
6
29
1
363
14,687
I think most of the error comes from not using a proper 4-wire Kelvin shunt. The 5 mOhm resistor may not be very accurate either, and it seems to drift as it heats up under a long heavy load. All these errors add up and make the readings drift even more.
1
18
1,777
PCB showed up yesterday. I soldered it this morning, connected it to my bench, fired up Codex, and a little while later... the firmware was done. 😄 4 days from PCB design to working firmware.
Tτ@teraytechJul 29
Today's project: XT60 Power Meter with an LM5060 + N-MOSFET high-side load switch, designed for testing batteries and other power electronics. I was going to buy one... but then I realized none of them had a high-side switch. So I built my own.
1
8
117
5,461
3
810
It’s just like modern EVs ditching physical buttons. But for VNAs that cost $ 10-100k, Zero idea what the designers were thinking.
Daniel Bogdanoff
@DanielBogdanoffJul 30
so how do you feel about soft/screen front panels?
10
7
95
5,252
Today's project: XT60 Power Meter with an LM5060 + N-MOSFET high-side load switch, designed for testing batteries and other power electronics. I was going to buy one... but then I realized none of them had a high-side switch. So I built my own.
4
6
1
151
11,411
The LM5060 monitors UVLO, OVP, and OCP, and cuts off the power path instantly if anything goes wrong. It's perfect for battery charge/discharge testing, and it has automotive-grade models
8
811
Tτ retweeted
wanl1n@wanl1nJul 29
我带来了vrchat同人 chocolat＆chiffon宝宝的玩偶 贩售链接开在bilibili 暂时还不支持国外的大家购买，我们正在努力T T 每只贩售达100只会给我们每一个下单的人送上对应角色的小粒牌，先提前感谢大家的购买！ 转发这条帖子，关注我，抽一位送一只 可折现50rmb 非常感谢大家的支持！
16
1
33
1,927
It’s working! 😆 My IT8510 can only pull out 120W max and it can survive for around 5 seconds :) Huge thanks to @AHBPROT for spending a whole day of the weekend vibe debugging this The ripple 297mVp-p still needs some improvement. Might need more MLCCs
Tτ@teraytechJan 28
3
4
1
99
5,298
Under 12V input and 20V/6A output conditions (120W), TPS55288 operation is limited by thermal performance. The junction temperature rise rapidly, triggering the 175°C thermal shutdown protection after approximately 6–10 seconds.
1
3
536
レアな日本語版 MSO-X シリーズフロントパネルステッカーをプレゼントしてくれた @AHBPROT に感謝！！ めちゃくちゃかっこいい🥹✨
2
2
69
2,606
Load more